Little Giant Classical Fountains

Invigorate tired outdoor spaces with easy-to-set-up water fountains. These attractive, self-contained water fountains make the perfect DIY weekend project. There is no complicated installation or construction involved to set up and enjoy these Classical Fountains. Made from durable molded polyethylene, Little Giant Classical Fountains are sure to provide season after season of reliable use. Call them nostalgic, rustic, or artistic, these hand-finished water fountains boast realistic colors and accents brimming with charm. Planter models feature an integrated planter with an anti-clog design to prevent soil or debris from damaging included UL-listed Little Giant submersible pump.

Please click on "More Information" for assembly instructions.

1. Operate the pump in clean, fresh water completely submerged. Do not let the pump run dry.
2. The pump can be placed in any position. There are suction cup feet provided with the pump. To install the suction cups, wet the ends and slide them into the slots on the bottom of the pump housing.
3. Support the weight of the pump adequately. Do not support the pump by the discharge connection alone.
4. There are two discharge adaptors provided with the pump. The larger adaptor is designed for use with 1/2" ID tubing. The smaller adaptor is designed for use with 3/8" ID tubing.
5. Adjust the flow rate by sliding the flow control located on the front of the pump. To reduce the flow rate further, place a valve on the discharge side of the pump or, if flexible tubing is used, a clamp on the tubing.
6. If the pump will be idle for an extended period, clean it according to the following Service Instructions.

Service Instructions
Disconnect the pump from the power source before attempting to service or remove any component.
Warning: Do not modify, cut, saw, sand or grind any part of the pump. Doing so can cause harmful emissions.

Note: This pump is permanently lubricated. Oiling is not required.

1. To disassemble the pump for cleaning, remove the front plate by gently squeezing on the sides of the screen and pulling it from the main body.
2. Remove the impeller. Note: The impeller shaft is pressed into the pump housing. Do not attempt to remove the shaft.
3. Use a small brush or a stream of water to clean any corrosion or debris from the impeller, shaft and impeller cavity.
4. Reassemble the parts in reverse order.
5. Inspect the power cord to ensure that it is in good condition and has no nicks or cuts.
6. If, after servicing, the pump trips its circuit breaker or GFCI, or otherwise does not operate properly, return to Little Giant or an authorized service center. Do not attempt repairs yourself.

Maintenance

• Do not allow the pump to run without water or allow it to freeze.
• Clean fountain out only with water and, if desired, use only a tablespoon of chlorine to prevent algae. DO NOT USE BLEACH. It may tarnish the applied finish.

Whiskey Barrel Fountain

Assembly Instructions

1. Remove fountain assembly and all packaging from box and place on a smooth flat surface. Please note that suction cups and adapter are not required for this application and therefore are not included.
2. Remove ornamental pump assembly from barrel and remove packaging.
3. Locate molded-on dowel/guide pin on underside of ornamental pump assembly.
4. Place electric pump into barrel.
5. Nest dowel/guide pin on underside of assembly into hole on edge of barrel.
6. Ensure power cord from pump is recessed into channel on underside of assembly and trailing to rear.
7. Center assembly on edge of barrel.
8. Use a Phillips head screwdriver to tighten screws. DO NOT OVER-TIGHTEN.
9. Fill the barrel with water until the electric pump is fully submersed.

Cottage Cauldron Fountain

Assembly Instructions

1. Remove fountain assembly and all packaging from box and place on a smooth flat surface. Please note that suction cups and adapter are not required for this application and therefore not included.
2. Remove ornamental pump from cauldron.
3. Locate flexible tubing on ornamental pump and connect tube to electric pump. Feed the electrical plug through the center hole at the top of the cauldron and then through the overfill hole at the base of the cauldron, allowing the electrical pump to go through the center hole but sit at the bottom of the cauldron.
4. Fill the inside of the cauldron with water until the electric pump is fully submersed.
5. Line up ornamental pump on the cauldron and loosen mounting bolts so that the ornamental pump can stand flat on the top surface.
6. Tighten the mounting bolts into mounting holes using a wrench. DO NOT OVER-TIGHTEN.

Copper Kettle Fountain

Assembly Instructions

1. Remove fountain assembly and all packaging from box and place on a smooth flat surface. Please note that suction cups and adapter are not required for this application and therefore not included.
2. Remove jug from kettle.
3. Locate flexible tubing on the jug and connect tube to electric pump.
4. Feed the electrical plug through the center hole at the top of the kettle and then through the 1-1/8" hole in the side of the basin. The pump should rest on the bottom of the kettle.
5. Fill the inside of the kettle with water, ensuring the electric pump is fully immersed.
6. Seat jug on the kettle in its location hole.
7. Plug in electric pump and allow 10 seconds for the jug to fill with water.

We're sorry!

No testimonials have been submitted for this product.

Would you like to submit a testimonial? Click here